To clarify the formation mechanism of periodic nanometer-size cavity structure of a borosilicate glass sample, the free electron density around the exit surface was investigated when it exposed to intense femtosecond laser radiation. The electron density near the edge of the crack on the surface was estimated to be 1020-1022 cm-3. From this result, the temperature of the irradiated heating area near the edge of the crack was estimated to reach at least about 6,000 K, which was sufficient for the initiation and propagation of the fiber fuse. In this way, periodic nanosized cavities could be formed by fiber fuse propagation starting near the edge of the crack on the exit surface. Next, fiber fuse propagation in the modified zone formed by continuous-wave laser irradiation in a silica glass sample was investigated theoretically by the explicit finite-difference method using the thermochemical SiOx production model. In the calculation, we assumed the glass to be in an atmosphere and that part (40 mm in length) of the modified zone was heated to a temperature of 2,923 K. The calculated velocities of fiber fuse propagation in the modified zone were in fair agreement with the experimental values observed at 0.514 and 1.064 mm.
| Published in | Journal of Electrical and Electronic Engineering (Volume 10, Issue 1) |
| DOI | 10.11648/j.jeee.20221001.11 |
| Page(s) | 1-9 |
| Creative Commons |
This is an Open Access article, distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution and reproduction in any medium or format, provided the original work is properly cited. |
| Copyright |
Copyright © The Author(s), 2022. Published by Science Publishing Group |
Bulk Glass, Fiber Fuse Phenomenon, Finite-difference Technique
| [1] | Gross S. and Withford M. J. (2015). Ultrafast-laser-inscribed 3D integrated photonics: challenges and emerging applications. Nanophotonics, 2015 (4), 332-352. |
| [2] | Glezer E. N., Milosavljevic M., Huang L., Finlay R. J., Her T. H., Callan J. P., and Mazur E. (1996). Three-dimensional optical strage inside transparent materials. Opt. Lett., 21 (24), 2023-2025. |
| [3] | Beresna M., Jung Y., Wang Y., Hayes J., Alam S. U., Brambilla G., and Richardson D. J. (2017). Independent core attenuation control in multicore fibers by direct femtosecond laser inscription. Optical Fiber Commun. Conf. (OFC2017), W3H.1. |
| [4] | Yamashita Y., Matsui T., Sakamoto T., Aozasa S., Wada M., Mori T., and Nakajima K. (2020). Reduction of differential mode gain in a two-mode amplifier using a void-inscribed EDF. Appl. Opt., 59 (3), 9574-9580. |
| [5] | Glezer E. N. and Mazur E. (1997). Ultrafast-laser driven micro-explosions in transparent materials. Appl. Phys. Lett., 71 (7), 882-884. |
| [6] | Du D., Liu X., Korn G., Squier J., and Mourou G. (1994). Laser-induced breakdown by impact ionization in SiO2 with pulse widths from 7 ns to 150 fs. Appl. Phys. Lett., 64 (23), 3071-3073. |
| [7] | Stuart B. C., Feit M. D., Rubenchik A. M., Shore B. W., and Perry M. D. (1995). Laser-induced damage in dielectrics with nanosecond to subpicosecond pulses. Phys. Rev. Lett., 74 (12), 2248-2251. |
| [8] | Stuart B. C., Feit M. D., Herman S., Rubenchik A. M., Shore B. W., and Perry M. D. (1996). Optical ablation by high-power short-pulse lasers. J. Opt. Soc. Am. B, 13 (2), 459-468. |
| [9] | Stuart B. C., Feit M. D., Herman S., Rubenchik A. M., Shore B. W., and Perry M. D. (1996). Nanosecond-to-femtosecond laser-induced breakdown in dielectrics. Phys. Rev. B, 53 (4), 1749-1761. |
| [10] | Von der Linde D. and Schüler H. (1996). Breakdown threshold and plasma formation in femtosecond laser-solid interaction. J. Opt. Soc. Am. B, 13 (1), 216-222. |
| [11] | Lenzner M., Krüger J., Sartania S., Chen Z., Spielmann C., Mourou G., Kautek W., and Krausz F. (1998). Femtosecond optical breakdown in dielectrics. Phys. Rev. Lett., 80 (18), 4076-4079. |
| [12] | Schaffer C. B., Brodeur A., and Mazur E. (2001). Laser-induced breakdown and damage in bulk transparent materials induced by tightly focused femtosecond laser pulses. Meas. Sci. Technol., 12, 1784-1794. |
| [13] | Smith A. V. and Do B. T. (2008). Bulk and surface laser damage of silica by picosecond and nanosecond pulses at 1064 nm. Appl. Opt., 47 (26), 4812-4832. |
| [14] | Smith A. V., Do B. T., Hadley G. R., and Farrow R. L. (2009). Optical damage limits to pulse energy from fibers. IEEE J. Selected Topics in Quantum Electron., 15 (1), 153-158. |
| [15] | Davis K. M., Miura K., Sugimoto N., and Hirao K. (1996). Writing waveguides in glass with a femtosecond laser. Opt. Lett., 21 (21), 1729-1731. |
| [16] | Miura K., Qiu J., Inouye H., Mitsuyu T., and Hirao K. (1997). Photowritten optical waveguides in various glasses with ultrashort pulse laser. Appl. Phys. Lett., 71 (23), 3329-3331. |
| [17] | Schaffer C. B., Brodeur A., García J. F., and Mazur E. (2001). Micromachining bulk glass by use of femtosecond laser pulses with nanojoule energy. Opt. Lett., 26 (2), 93-95. |
| [18] | Kanehira S., Si J., Qiu J., Fujita K., and Hirao K. (2005). Periodic nanovoid structures via femtosecond laser irradiation. Nano Lett., 5 (8), 1591-1595. |
| [19] | Kanehira S., Miura K., Fujita K., and Hirao K. (2006). Nano-sized modification of transparent materials using femtosecond laser irradiation. Proc. Soc. Photo-Opt. Instrum. Eng., 6413, 6413M1-6413M9. |
| [20] | Tzortzakis S., Sudrie L., Franco M., Prade B., Mysyrowicz A., Couairon A., and Bergé L. (2001). Self-guided propagation of ultrashort IR laser pulses in fused silica. Phys. Rev. Lett., 87 (21), 213902-1-213902-4. |
| [21] | Sudrie L., Couairon A., Franco M., Lamouroux B., Prade B., Tzortzakis S., and Mysyrowicz A. (2002). Femtosecond laser-induced damage and filamentary propagation in fused silica. Phys. Rev. Lett., 89 (18), 18660-1-18660-4. |
| [22] | Wu Z., Jiang H., Luo L., Guo H., Yang H., and Gong Q. (2002). Multiple foci and a long filament observed with focused femtosecond pulse propagation in fused silica. Opt. Lett., 27 (6), 448-450. |
| [23] | Wu Z., Jiang H., Sun Q., Yang H., and Gong Q. (2003). Filamentation and temporal reshaping of a femtosecond pulse in fused silica. Phys. Rev. A, 68, 063820. |
| [24] | Kashyap R. and Blow K. J. (1988). Observation of catastrophic self-propelled self-focusing in optical fibres. Electron. Lett., 24 (1), 47-49. |
| [25] | Kashyap R. (1988). Self-propelled self-focusing damage in optical fibres. Lasers'87: Proc. Xth Int. Conf. Lasers and Applications, 859-866, STS Press, McLean. |
| [26] | Hand D. P. and Russell P. St. J. (1988). Solitary thermal shock waves and optical damage in optical fibers: the fiber fuse. Opt. Lett., 13 (9), 767-769. |
| [27] | Hand D. P., Townsend J. E., and Russell P. St. J. (1988). Optical damage in fibers: the fiber fuse. Proc. Conf. on Lasers and Electro-Optics (CLEO), WJ1. |
| [28] | Hand D. P. and Russell P. St. J. (1988). Soliton-like thermal shock-waves in optical fibres: origin of periodic damage tracks. Proc. Eur. Conf. Opt. Commun., 111-114. |
| [29] | Yoshioka M., Hidai H., and Tokura H. (2006). CW-laser induced modification in glasses by laser backside irradiation (LBI). Proc. Soc. Photo-Opt. Instrum. Eng., 6106, 61060Y-1-61060Y-9. |
| [30] | Hidai H., Yoshioka M., Hiromatsu K., and Tokura H. (2009). Glass modification by continuous-wave laser backside irradiation (CW-LBI). Appl. Phys. A, 96, 869-872. |
| [31] | Hidai H., Yoshioka M., Hiromatsu K., and Tokura H. (2010). Structual changes in silica glass by continuous-wave laser backside irradiation. J. Am. Ceram. Soc., 93 (3), 1597-1601. |
| [32] | Itoh S., Hidai H., and Tokura H. (2013). Experimental and numerical study of mechanism of glass modification process by continuous-wave laser backside irradiation (CW-LBI). Appl. Phys. A, 112, 1043-1049. |
| [33] | Tokunaga D., Sato S., Hidai H., Matsusaka S., Chiba A., and Morita N. (2019). A novel method of triggering fiber fuse inside glass by optical breakdown and glass drilling as its application. Appl. Phys. A, 125, 400. |
| [34] | Shuto Y., Yanagi S., Asakawa S., Kobayashi M., and Nagase R. (2004). Fiber fuse phenomenon in step-index single-mode optical fibers. IEEE J. Quantum Electron., 40 (8), 1113-1121. |
| [35] | Shuto Y. (2014). Heat conduction modeling of fiber fuse in single-mode optical fibers. J. Photonics, 2014, 645207. |
| [36] | Shuto Y. (2015). Simulation of fiber fuse phenomenon in single-mode optical fibers. Advances in Optical Fiber Technology, Eds. Yasin M., Arof H., and Harun S. W., Chap. 5, 159-197, InTech, Rijeka. |
| [37] | Shuto Y. (2010). Evaluation of high-temperature absorption coefficients of ionized gas plasmas in optical fibers. IEEE Photon. Technol. Lett., 22 (3), 134-136. |
| [38] | Giuliano C. R. (1964). Laser-induced damage to transparent dielectric materials. Appl. Phys. Lett., 5 (7), 137-139. |
| [39] | Fersman I. A. and Khazov K. D. (1970). Damage of transparent dielectric surfaces by a laser beam. Sov. Phys. Tech. Phys., 15, 834-838. |
| [40] | Giuliano C. R. (1972). Laser-induced damage in transparent dielectrics: The relationship between surface damage and surface plasmas. IEEE J. Quantum Electron., QE-8 (9), 749-754. |
| [41] | Crisp M. D., Boling N. L., and Dubé G. (1972). Importance of Fresnel reflections in laser surface damage of transparent dielectrics. Appl. Phys. Lett., 22 (8), 364-366. |
| [42] | Boling N. L., Crisp M. D., and Dubé G. (1973). Laser induced surface damage. Appl. Opt., 12 (4), 650-660. |
| [43] | Génin F. Y., Salleo A., Pistor T. V., and Chase L. L. (2001). Role of light intensification by cracks in optical breakdown on surfaces. J. Opt. Soc. Am. A, 18 (10), 2607-2616. |
| [44] | Bloembergen N. (1974). Laser-induced electric breakdown in solids. IEEE J. Quantum Electron., QE-10 (3), 375-386. |
| [45] | Bloembergen N. (1973). Role of cracks, pores, and absorbing inclusions on laser induced damage threshold at surfaces of transparent dielectrics. Appl. Opt., 12 (4), 661-664. |
| [46] | Shuto Y. (2020). Cavity pattern formation and its dynamics of fiber fuse in single-mode optical fibers. J. Informatics Math. Sci., 12 (4), 271-288. |
| [47] | Jensen B. (1985). The quantum extension of the Drude-Zener theory in polar semiconductors. Handbook of Optical Constants of Solids, Ed. Palik E. D., Chap. 9, Academic Press Inc., New York. |
| [48] | Chemical Society of Japan. (1984). Chemical Data Book, 3rd Ed., Chap. 14, Maruzen, Tokyo. |
| [49] | Shuto Y. (2016). End face damage and fiber fuse phenomenon in single-mode fiber-optic connectors. J. Photonics, 2016, 2781392. |
| [50] | Davis D. D., Mettler S. C., and DiGiovani D. J. (1996). A comparative evaluation of fiber fuse models. Proc. Soc. Photo-Opt. Instrum. Eng., 2966, 592-606. |
| [51] | Shibata N. and Edahiro T. (1982). Refractive-index dispersion for GeO2-, P2O5- and B2O3-doped silica glasses in optical fibers. Trans. IECE Jpn., E65 (3), 166-172. |
| [52] | Smith W. L. (1978). Laser-induced breakdown in optical materials. Opt. Eng. 17 (5), 489-503. |
APA Style
Yoshito Shuto. (2022). Electron Density Estimation and Fiber Fuse Simulation in Laser-Irradiated Bulk Glass. Journal of Electrical and Electronic Engineering, 10(1), 1-9. https://doi.org/10.11648/j.jeee.20221001.11
ACS Style
Yoshito Shuto. Electron Density Estimation and Fiber Fuse Simulation in Laser-Irradiated Bulk Glass. J. Electr. Electron. Eng. 2022, 10(1), 1-9. doi: 10.11648/j.jeee.20221001.11
AMA Style
Yoshito Shuto. Electron Density Estimation and Fiber Fuse Simulation in Laser-Irradiated Bulk Glass. J Electr Electron Eng. 2022;10(1):1-9. doi: 10.11648/j.jeee.20221001.11
Share This Article
Twitter
Linked In
Facebook
Copy
Download@article{10.11648/j.jeee.20221001.11,
author = {Yoshito Shuto},
title = {Electron Density Estimation and Fiber Fuse Simulation in Laser-Irradiated Bulk Glass},
journal = {Journal of Electrical and Electronic Engineering},
volume = {10},
number = {1},
pages = {1-9},
doi = {10.11648/j.jeee.20221001.11},
url = {https://doi.org/10.11648/j.jeee.20221001.11},
eprint = {https://article.sciencepublishinggroup.com/pdf/10.11648.j.jeee.20221001.11},
abstract = {To clarify the formation mechanism of periodic nanometer-size cavity structure of a borosilicate glass sample, the free electron density around the exit surface was investigated when it exposed to intense femtosecond laser radiation. The electron density near the edge of the crack on the surface was estimated to be 1020-1022 cm-3. From this result, the temperature of the irradiated heating area near the edge of the crack was estimated to reach at least about 6,000 K, which was sufficient for the initiation and propagation of the fiber fuse. In this way, periodic nanosized cavities could be formed by fiber fuse propagation starting near the edge of the crack on the exit surface. Next, fiber fuse propagation in the modified zone formed by continuous-wave laser irradiation in a silica glass sample was investigated theoretically by the explicit finite-difference method using the thermochemical SiOx production model. In the calculation, we assumed the glass to be in an atmosphere and that part (40 mm in length) of the modified zone was heated to a temperature of 2,923 K. The calculated velocities of fiber fuse propagation in the modified zone were in fair agreement with the experimental values observed at 0.514 and 1.064 mm.},
year = {2022}
}
TY - JOUR T1 - Electron Density Estimation and Fiber Fuse Simulation in Laser-Irradiated Bulk Glass AU - Yoshito Shuto Y1 - 2022/01/18 PY - 2022 N1 - https://doi.org/10.11648/j.jeee.20221001.11 DO - 10.11648/j.jeee.20221001.11 T2 - Journal of Electrical and Electronic Engineering JF - Journal of Electrical and Electronic Engineering JO - Journal of Electrical and Electronic Engineering SP - 1 EP - 9 PB - Science Publishing Group SN - 2329-1605 UR - https://doi.org/10.11648/j.jeee.20221001.11 AB - To clarify the formation mechanism of periodic nanometer-size cavity structure of a borosilicate glass sample, the free electron density around the exit surface was investigated when it exposed to intense femtosecond laser radiation. The electron density near the edge of the crack on the surface was estimated to be 1020-1022 cm-3. From this result, the temperature of the irradiated heating area near the edge of the crack was estimated to reach at least about 6,000 K, which was sufficient for the initiation and propagation of the fiber fuse. In this way, periodic nanosized cavities could be formed by fiber fuse propagation starting near the edge of the crack on the exit surface. Next, fiber fuse propagation in the modified zone formed by continuous-wave laser irradiation in a silica glass sample was investigated theoretically by the explicit finite-difference method using the thermochemical SiOx production model. In the calculation, we assumed the glass to be in an atmosphere and that part (40 mm in length) of the modified zone was heated to a temperature of 2,923 K. The calculated velocities of fiber fuse propagation in the modified zone were in fair agreement with the experimental values observed at 0.514 and 1.064 mm. VL - 10 IS - 1 ER -
Email: